#Checksum generate tool checksum.ini code

There is a lot of cunfusion on the internet about this, and i might even be wrong. It's how easily it will be picked to spawn.Īlso the initial spawn rate after dino wipe combined with spawn max. It's not how much will spawn, thats the Percentage line.

This just means how much chance it has to be drawn from the list to be spawned.Įxept for when you want something to be rare or not spawn all the time, then you just put it lower than the others.

Rare creatures: if you want a creature to be rare set it to 0.001 and it's Entry Weight lower than the others. Overspawn: creatures that overspawn are best set to 0.001 and will still be plenty. So if you have 10 dinos but want more turtles on your beach you can set that to 0.4 (all dinos in that area, like on all beaches) So go ingame to see how its spawning and adjust accordingly.įor each dino you have to set how much of them you want in that area. Beavers, Snakes, Spino, Crabs overspawn, so does some others. Do some tests, because that creature might not want to spawn there, or might completely overspawn. 500 snakes in an area might not be so fun. Think wisely how you want to configure your map. In this case there is only one spawn location but on the map you'll see that 1 spawn location can affect several areas on the map. Turn off the other locations so the lication you want to know is the only one. It will show in the left top corner a list of locations this creature spawns. It's the Ragnarok map but you find the ither maps on that site too. Go to the Spawn Entries site (locations). Dont forget to do the same in the second half. Now if you want more the 10 species you can select parts 1-9 and copy/paste them under itself. If you are going to have less than 10 species, fill that Dino10 part in 1st. They have a few different symboles so better to not touch those. If you want less species you can simply remove the blocks you are not usingīut never remove the 2 parts with Dino10 (last part in 1st and 2nd half) Replace both of them by the same Dino ID. In the first half there is a Dino1 but also in the second half. Then you need to add Raptor_Character_BP_C Each location, spawner, and species has ' before and after it's name. In this list you also see what normally spawns there. Make sure you are looking at spawn locations of the correct map. The names of the locations can be found here. That is where you need to put the location. (NPCClassString='Dino10', MaxPercentageOfDesiredNumToAllow=0.1))) (NPCClassString='Dino9', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino8', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino7', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino6', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino5', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino4', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino3', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino2', MaxPercentageOfDesiredNumToAllow=0.1), (NPCClassString='Dino1', MaxPercentageOfDesiredNumToAllow=0.1), (AnEntryName='Spawn10', EntryWeight=1.0, NPCsToSpawnStrings=('Dino10'))), (AnEntryName='Spawn9', EntryWeight=1.0, NPCsToSpawnStrings=('Dino9')), (AnEntryName='Spawn8', EntryWeight=1.0, NPCsToSpawnStrings=('Dino8')), (AnEntryName='Spawn7', EntryWeight=1.0, NPCsToSpawnStrings=('Dino7')), (AnEntryName='Spawn6', EntryWeight=1.0, NPCsToSpawnStrings=('Dino6')), (AnEntryName='Spawn5', EntryWeight=1.0, NPCsToSpawnStrings=('Dino5')), (AnEntryName='Spawn4', EntryWeight=1.0, NPCsToSpawnStrings=('Dino4')), (AnEntryName='Spawn3', EntryWeight=1.0, NPCsToSpawnStrings=('Dino3')), (AnEntryName='Spawn2', EntryWeight=1.0, NPCsToSpawnStrings=('Dino2')), (AnEntryName='Spawn1', EntryWeight=1.0, NPCsToSpawnStrings=('Dino1')), If that's what you want you'll also have to include all the dinos that were in that area.ĬonfigOverrideNPCSpawnEntriesContainer=( NPCSpawnEntriesContainerClassString='DinoSpawnEntry1', NPCSpawnEntries=( You can't just 'add' a creature to a location this way. On my phone i have Jota+ and it makes working with ini coding super easy.īTW this completely removes all dinos from that area and only the ones you put in here will be in that area. To get started copy the part in between the lines and paste them into your text editor. (but easy to adjust to any number from 3 and up) Now we have a template that is easy to edit Took that appart and copied the ones in the middle so all the syntax would be correct.

#Checksum generate tool checksum.ini code

I looked for a code that had at least 3 species.